Swing Check Valve With Hammer HH44T

Performance Parameters:

1.Conforms to MSs Sp-71.

2.Face to face dimensions con for is to ANSI B16.10(1251b)

3.Flanges drilled conforms to ANSI B16.1(1251b)

4.Suitable me die:Water.Oil.Gas

Envíenos un correo electrónico

Detalle del producto

Swing Check Valve With Hammer Definition and Components

Lista de comprobación de la inspección:

Functional Swing Test: This is key. Hold the valve in its installed orientation (disc hinge horizontal). The disc must swing freely and fully open by its own weight when the valve body is tilted, and fall closed smoothly without sticking.
Pressure Testing: Perform shell test and seat leakage test per API 594. For a metal-seated valve (bronze-on-metal), a slight weep per the standard is acceptable, but major leakage is not.
Dimensional Check: Verify face-to-face length and flange dimensions/drilling against the order specification.
Visual Inspection: Check for proper machining of the seat face and absence of defects in the disc sealing surface.

Precauciones para la exportación:

Secure the Disc: Before crating, tie the disc in the fully closed position using wire or plastic straps. This prevents it from swinging violently during handling and damaging the hinge pin or seat.
Protect Flange Faces: Use sturdy, bolted plastic or wooden covers on the flange faces to protect the sealing surfaces and bolt holes.
Internal Preservation: Apply a light, removable anti-corrosion coating to internal metal surfaces, especially the disc and seat.
Proper Packaging: Use a robust wooden crate. Due to the valve's asymmetric weight distribution (the disc and cover assembly), ensure it is blocked and braced to prevent movement. Mark the crate with "SWING CHECK VALVE" and "KEEP HORIZONTAL" handling instructions.

Role, Characteristics, and Application Scenarios of Swing Check Valve With Hammer in Pipelines

Water supply valve Funciones de canalización:

Positive Backflow Prevention: Standard check valve function.
Controlled, Forced Closure: The external weight ensures the disc closes firmly and decisively, even under low reverse pressure or in the presence of flow disturbances that might cause a standard swing check to chatter or remain partially open.
Disc Flutter Prevention: The added inertia dampens oscillations.

Características operativas:

Adjustable Closing Force: The position of the weight on the lever arm is adjustable, allowing tuning of the closing speed and force to match system dynamics.
Ensures Tight Seal: Provides additional seating force, improving shut-off compared to gravity-alone designs.
External Mechanism: Requires more space and is more susceptible to environmental damage/corrosion than an internal design.
Horizontal Installation Only: Must be installed with the lever assembly oriented correctly (typically upwards).

Escenarios de aplicación:

Used in systems where a standard swing check valve is unreliable due to slow flow, low backpressure, or pulsating conditions that cause disc flutter.

Low-Flow or Low-Pressure Pump Discharge: Ensures closure when reverse pressure is minimal.
Compressed Air/Gas Systems: Prevents flutter in pulsating flow.
Vertical Pump Discharge (into overhead lines): Where the disc might not close reliably by gravity alone due to line geometry.
Steam Return Lines: To ensure positive closure.

Check Valve for Water Diagrama del escenario (Descripción del texto):

In an industrial compressed air system, a reciprocating compressor sends pulsating air flow into a receiver tank via a horizontal pipeline. A standard swing check valve on the discharge would chatter violently with each compressor stroke. Instead, an HH44T Swing Check Valve with Hammer is installed. The adjustable weight on the external lever is set to provide significant closing force. When the compressor piston stops on its return stroke, the weighted lever immediately and forcefully slams the disc shut against its bronze seat, preventing backflow into the compressor cylinder. This action happens consistently with every stroke, eliminating damaging flutter and ensuring efficient operation, even though the forward air pressure might be relatively low at the moment of closure.

Swing Check Valve With Hammer Standards: Materials, Design, and Connections

Normas materiales:

Body & Cover: Cast Iron (ASTM A126), Ductile Iron (ASTM A536).
Disc: Bronze or Cast Iron.
Seat Ring: Bronze (ASTM B62).
Lever Arm & Weight: Carbon Steel, often galvanized.
Shaft Extension: Stainless Steel.

Normas de diseño:

API 594: Check Valves: Flanged, Lug, Wafer, and Butt-welding.
ASME B16.34: Valores nominales de presión y temperatura de las válvulas.
MSS SP-71: Cast Iron Swing Check Valves.

Normas de conexión:

Flanges: ASME B16.1 Class 125/250, Raised Face (RF).

How to Select Swing Check Valve With Hammer

Pasos clave:

Identify the Need for Forced Closure: Specify this valve if system analysis indicates problems with disc flutter, slow closure, or unreliable sealing with a standard swing check.
Specify the Weight Setting: Provide the desired closing characteristics or system data (flow rates, pressures) so the manufacturer can pre-set the weight position. Ensure the lever and weight are sized for the valve.
Consider the Environment: The external mechanism is exposed. For corrosive or outdoor environments, specify appropriate coatings or materials for the lever and weight.
Verify Space and Orientation: Confirm there is adequate clearance for the lever to swing freely and that the installation will be horizontal.

Pre-Shipment Inspection for Export Swing Check Valve With Hammer and Key Considerations